like 200 i Manuel atelier : Page 115

          12. FUEL SYSTEM                                                                                                  LIKE 200i


          Failure
 Blinks                       Fault Description         Priority                       Fault Management
          Codes
                                                                   1. Check wiring and connections.
  12      P0230     Fuel Pump Relay Fault                  2
                                                                   2. Listen for relay clicking when ignition is switched on.
                                                                   1. Engine exceeded 10,500 rpm redline.
  13      P0219     Engine Over Speed Condition Fault      2       2. Check belt.
                                                                   3. Check spark plug. Use resistor plug "R".
                                                                   1.Use volt meter to check ECU pin 18 (5 volts DC) or
                                                                   use diagnostic tool (5 volts +/- 0.1 volts).
                                                                   2.Check voltage difference between pin 16 and pin 18
                                                                   (5 volts DC).
  14      P1560         Sensor Power Supply Fault          2
                                                                   3.Cylinder head Temperature Sensor, Intake Air
                                                                   Temperature Sensor, and TPS use the same power
                                                                   supply. If getting more than three faults, ECU could be
                                                                   faulty.
                                                                   1.If engine exceeds 3250 rpm at idle, ECU will lower
                                                                   engine idle speed or shut engine down.
                                                                   2.When start the engine, Do NOT use throttle
  15      P0700     Engine RPM/CVT Fault                   2       3.Check throttle cables and throttle body for sticking
                                                                   and binding.
                                                                   4.Check throttle idle voltage (0.68 volts +/- 0.03 volts).
                                                                   5.Check CVT belt.
                                                                   1.Use voltmeter to check resistance (cold 2445.2-
  16      P0115     Cylinder Head Thermosensor Fault       2       5458.3 ohms).
                                                                   2.Check wiring and connections for ECU pin 9.
                                                                   1.Check bulb (1.7w 12 volt DC).
  18      P0650     Check Engine Light Fault               3
                                                                   2.Check ECU wiring and connections pin 4.
                                                                   1.Check sensor voltage (5 volts +/- 0.1 volt).
                                                                   2.Check ECU wiring and connections pin 8.
  21      P0105     Atmosphere Pressure Sensor Fault       2
                                                                   3.Use Diagnostic Tool to check pressure (101.3 +/- 3
                                                                   KPA).
                                                                   1.Use KYMCO AFI Diagnostic Tool Check sensor
                                                                   voltage (3.5~4.7 volts ).
  22      P1110     Bank Angle Detector Sensor Fault       2
                                                                   2.Check ECU wiring and connections pin 11.
                                                                   3.If still getting fault, replace sensor.
                                                                   1.Check sensor resistance (Standard: 6.7~9.5@20
                                                                   ~30  ).
  23      P0136     O2 Sensor Fault                        1
                                                                   2.Check ECU wiring and connections pin 10.
                                                                   3.If still getting fault, replace sensor.
                                                                   1. Check ECU wiring and connections pin 14.
  24      P0141     O2 Heater Sensor Fault                 2
                                                                   2. If still getting fault, replace sensor.
                                                                   1. Check wiring and connections pins 10 and 14.
                                                                   2. If still getting fault, the injector probably injected
  25      P0171     Close loop Fault                       1       more fuel or inlet air adnormal. Check if the injector is
                                                                   cloged, if the valve timing is correct or valve leaking, if
                                                                   the piston and ring piston is damaged....and so on.




12-9